Burbank, Los Angeles County
Heat Pump Installation in Burbank, CA
Burbank homeowners run their cooling systems hard through long, hot San Fernando Valley summers, and many are carrying oversized AC units that drive electric bills higher than they need to be. A properly sized heat pump replaces that inefficient setup with one system that handles both heating and cooling year-round. Build Bright Home Solutions installs ducted and ductless heat pump systems, including full gas-to-electric conversions, for Burbank residents who are planning ahead and want the job done right the first time. Our team brings mechanical, electrical and building-envelope expertise under one roof, so we size, install and verify your system without handing you off to a separate contractor. If you are ready to stop patching an aging AC and start with a system built for year-round performance, we are ready to move fast.
Free Home Systems Assessment
- HVAC • Electrical • Roofing • Insulation
- Professional Evaluation for Replacement Projects
Heat Pump Installation in Burbank
Burbank sits in the inland valley of Los Angeles County where summer cooling loads are extreme and homes tend to run air conditioning for a longer season than coastal communities. Many Burbank homes were built with central ducted systems sized for older, less efficient equipment, and attic conditions in the area often make heat gain worse than it needs to be. Replacing a legacy gas furnace and central AC combination with a modern heat pump addresses both the summer cooling load and winter heating in a single upgrade. Build Bright Home Solutions was founded in 2025 and is backed by 26 years of industry experience delivering mechanical, electrical and building-envelope upgrades across Southern California. That depth of experience means we understand the specific demands Burbank's climate places on equipment and we install systems sized to match actual load, not assumptions.
Do the envelope before the equipment. Sealing and insulating first means the replacement system can be smaller, cheaper and quieter.
What that involves
- Ducted heat pump installation sized for Burbank's high cooling loads, replacing existing central AC and furnace combinations
- Ductless mini-split heat pump installation for room additions, garages or homes without existing ductwork
- Gas-to-electric conversions that remove the furnace and connect a heat pump to existing or upgraded duct systems
- Load calculations and equipment selection to avoid the oversizing problems common with older Burbank HVAC installs
- Coordination of electrical panel work when your service needs an upgrade to support the new heat pump
Burbank
Heat Pump Installation questions from Burbank
- What should I expect during the heat pump installation process in Burbank?
- We start with a site visit to assess your existing equipment, duct condition and electrical service. From there we perform a load calculation to size the system correctly for your home and Burbank's climate. Installation typically involves removing the old equipment, setting the new outdoor unit, installing or connecting the indoor air handler, and verifying refrigerant charge and airflow before we leave. If your panel needs an upgrade to support the heat pump, we handle that as part of the same project so you are not coordinating multiple contractors.
- Can a heat pump handle Burbank summers, or will I need supplemental cooling?
- A properly sized heat pump handles the full cooling load in Burbank's inland valley climate without supplemental equipment. The key word is properly sized. Oversized systems short-cycle and leave humidity higher than it should be. We use load calculations based on your home's actual square footage, insulation, window area and orientation before we select equipment, which is how you get consistent comfort through the hottest stretches of the year.
- How does a gas-to-electric heat pump conversion work?
- We disconnect and remove the existing gas furnace and central AC condenser, then install a heat pump system that uses electricity for both heating and cooling. The new outdoor unit connects to your existing duct system if the ducts are in acceptable condition. We assess duct leakage and condition during the site visit. If the ducts need sealing or modification, we address that before commissioning the new system. Your gas line to the furnace is capped, and we verify the electrical service can support the new equipment.
- Do I need to upgrade my electrical panel to install a heat pump?
- Not always, but it depends on your current panel capacity and what other loads are already on it. Many Burbank homes have older 100-amp panels that are already close to capacity. During our site visit we check available capacity before recommending anything. If an upgrade is needed, we coordinate the electrical work as part of the heat pump project rather than sending you to find a separate electrician.
- Is a ductless mini-split a good option for my Burbank home?
- Ductless mini-splits work well for homes without existing ductwork, for room additions, converted garages or spaces that were never connected to the central system. They are also a strong option when duct condition is poor enough that replacing ducts would add significant cost. Each indoor unit handles one zone independently, which means you only condition the spaces you are using. We can help you evaluate whether a ducted or ductless approach makes more sense given your home's layout and existing infrastructure.
Heat Pump Installation in Burbank?
Call (818) 915-1604 and tell us about the building.